SDR HACK Part II – The Mod – Receive up to 4.5GHz on your RTLSDR for $5.00

If you'd rather buy one already modified visit my store at


In Part 1 I showed that a cheap satellite upconverter can be used as a microwave downconverter with some mods. In this post I'll show you the modifications needed, step-by-step tutorial style, and make lame jokes. After more experimentation and burned fingers today I've found a more efficient way to do the mod that provides a much stronger signal at the output of the downconverter! 

Soldering experience level: Moderate – SMD parts removal and fine soldering, but explained so the novice can complete it as well. 

Some tools you will need are:

  • Soldering Iron – Preferably with a very small tip. r
  • Solder – I use Sn63/Pb37 RA type
  • Tweezers – Fine tipped preferred but not required
  • Needle Nose Pliers or Screwdriver to take the case and shield apart.
  • Magnet Wire – 24 Ga or so. Tip: use unwound stranded wire in a pinch
  • Wire Cutters
  • Magnifying Glass or Goggles
  • Exacto Knife
  • Bright Light
  • Volt/Ohm Meter to test for shorts etc.
  • Patience 

SURGEON GENERAL'S WARNING: If you choose to use this information to modify your equipment you take all responsibility for any damage that may occur, up to and including the complete destruction of every device, computer, power grid, interplanetary starship, and/or non-gender specific restroom diaper changing station that may be in the vicinity. Also, I'm not responsible for you burning your own (or others – NTTAWWT) body parts or your wife's/husband's kitchen table. NOT MY FAULT!!! Besides, if you sue me you wouldn't get much. An old moody cat, some chickens that don't lay anymore, and some broken down ham radios. Continue at your own risk!

These boards are fairly forgiving so minor mistakes won't end your adventure. Just don't cross the streams when you can help it and don't hook it up to anything until the modification is complete. A general positive to ground short around the filters and such won't (shoudn't) kill it, but directly shorting the ICs on board or the regulator, well, no guarantees.  

First we'll remove all the parts that are in our way. Filters, DiSEqC stuff, etc. In the images below, parts marked with a red dot or line are to be removed from the board. I've found that by heating one side of the smd parts with the iron and applying a little pressure they will "flip" up on the opposite pad. From here you can use your tweezers to pull them off or apply a little more heat to the bottom side of the part to get it to release. Sometimes they'll stick to the iron, just flick or gently scrape them off. Don't worry about losing the removed parts. We're not going to be reusing them here.

We'll start on the input section of the board. Remember red dots or lines are parts to be removed.


After you have removed those there is a capacitor under all that glue that needs to be removed. Also, in the lower right you'll notice a red dot on a resistor. Go ahead and get it off there too.


In the next picture you need to cut the trace where the red line is marked. You could cut it between the solder blob and the 101 marked resistor if you like, just to avoid cutting the hole trace that we'll soon need. I've found that if I scrape across there with the tip of an exacto knife it goes a lot easier, even rolling the sharp edge up and applying plenty of pressure. The red dot in the lower left is the same as the one in the lower right in the previous picture, just to avoid confusion. The red dot in the upper right can be removed now too or wait until the step after this.


There are four parts marked for removal in this image, including the one mentioned in the previous step.




In this step you must VERY GENTLY bend the ceramic oscillator into an upright or leaning towards the IC position. The leads on this device are extremely fragile and it takes some force to bend it into an upright or forward leaning position. Take a small screwdriver or other tool, slide the tip in between the oscillator and the case, and gently apply pressure until it is in a position where you can use a finger tip to move it the rest of the way. It doesn't need to be bent all the way over, just enough to where you can safely reach your soldering iron tip to the board. If you move it around very much the oscillator WILL separate from the leads, so just get it into position and don't fool with it any more. We'll be coming back to this area in a future step. The first picture below is as it appears before adjusting the position.


And this is how it should appear after adjustment:


You've made it this far hopefully, now we begin wiring everything back up. For this part we'll need a small piece of magnet wire or similar about 12 inches (305mm) long. Cut it into pieces at the following lengths – leaving a little extra length on each for screw ups or mismeasurements. Two pieces at 2-1/2 inches (64mm) each, two pieces at 1-1/2 inches (39mm), two pieces at about 1-1/4 inch (32mm). 

If using magnet wire or any similar type that has a hard (painted on) coating, grab your exacto knife or whatever is handy and scrape about 1/16th inch (or 3-4mm) back on each end to expose the copper for soldering. Take your 1-1/4 inch (32mm) piece of wire and on one end strip back approx 1/2 inch (13mm). Don't bother with the other end., we're using it as a handle/prop. Once you have that ready make sure your soldering iron is clean, get your solder and tweezers ready, and continue to the next step. From here on out, areas marked with GREEN DOTS are where we will solder. GREEN LINES are the wire jumpers we are adding. 

In the following image the green dot indicates where you will place the 1 1/4 inch (32mm) piece of wire. You will slide it into the hole so that only the exposed copper is sticking out above the hole. If you have the converter laying flat about 1/4 inch of wire will stick up through the hole. If not, cut the wire shorter from the other end or slightly bend the wire to where it will stay put. Place a small amount of solder where the wire meets the board, taking care not to use too much solder or form an unwanted solder bridge to the adjacent ground plane. We're using this kick-stand technique because three other wires must be soldered here and it is very easy to bridge the solder or have the wires jump back up on you while adding the next. This makes it SO much easier, trust me. Once soldered into place flip the board over and apply a small amount of solder where the wire meets the board and trim the excess


This is the backside where you will solder and trim the excess. Once done flip the board back over and continue to the next step.


This image shows the beginning locations of where we are soldering from and too. Don't solder anything yet:


This next image shows the first three jumpers connecting the previously mentioned points. First take your 1-1/2 inch (39mm) wire and solder one side to the RF input, which is the big blob of solder middle far left. The solder that is there is nasty to get started so tin your iron tip a little to help the heat transfer fast. This is the most difficult part of the whole mod, solder (very little here) the other end of that wire to the capacitor marked in green in the far top left corner – solder it to the left side. Be very careful here as it is SO easy to create a solder bridge. If you have a solder sucker or solder braid you might keep it handy here. The wire should loop up a little bit once you're done there.

The next wire to solder is 2-1/2 inches (64mm) and starts at the left pad where I marked the capacitor for removal earlier. (The next green dot to the right of the RF input). Apply a small amount of solder to the pad, and place the wire before removing the iron. Stretch the wire out so it touches the kickstand wire. If it is way too long you can trim it some but remember to strip your wire back again. Don't solder it to the kickstand yet.

The final wire for this step begins at the bottom center green dot and you'll use the remaining 1-1/2 inch (39mm) wire. Solder one end to the bottom green dot and stretch the wire so it touches the kickstand wire.


In this step we'll attach the remaining 2-1/2 inch (64mm) wire and solder it and the other two wires to the kickstand. Be careful in behind the ceramic oscillator! This pic just shows the solder point behind the oscillator, the following picture shows this wire feeding back to the kickstand for soldering.


And the wire link:


Make sure to trim and scrape as necessary then solder all three wires to the kickstand – above board level so as not to bugger up the board or bridge to ground. Now is an excellent time to get your magnifying glass or goggles out and have a good look everywhere your soldering iron got near. Little solder balls can normally be popped loose with your exacto knife, but if necessary use the soldering iron and solder sucker or braid. Make sure you don't have any bridges to ground or other unintended traces. Only one more wire to go.

Flip the board over and solder the remaining 1-1/4 inch (32mm) wire as shown in the image below. This insures voltage gets to the PLL.


You'll need a bias tee that can provide 7-12v or so and feed from the SDR side (the side with the glued on cable). Make sure to hook your SDR or other radio to the correct side of the bias tee. You could fry your device, No fun!

Well, if you were able to stomach my rambling and you made it this far, Congratulations! You now have a microwave downconverter capable of up to 4.5GHz with an RTL-SDR dongle for much less than an expensive SDR. I make no claims on performance but it should be pretty decent considering the costs involved. Remember you'll probably need an LNA for many purposes in the microwave bands due to the low power nature of the services and the distances involved.

I hope this was helpful to you, if you have any questions I'll try to answer them in the comments below, on reddit, email, or whatever. I have 3 or 4 more of these laying here if someone needs one and isn't comfortable doing the mod themselves. Work out a trade or something. If you found this tutorial helpful leave a comment.

73's Chris – KD0CQ




About the Author

Chris - KD0CQ (formerly KB0TLW) has held an amateur (ham) radio license since 1994 and is stubbornly grasping onto his Advanced class operator status. His professional experience includes Network and Systems Administrator, Network Security, and Electronics Engineer. Sometimes even a little bit of web development. mail: chris at kd0cq dot com

43 Comments on "SDR HACK Part II – The Mod – Receive up to 4.5GHz on your RTLSDR for $5.00"

  1. Your articles are great. Licensed for 57 years. Eyesight is failing so wonder if you have an extra fully modified converter by Direct TV. Nothing to trade ut will pay you for your work. I am interested in S Band reception of deep space/lunar landers, rover and future USA return to the moon. Thanks so much for what you do.

    Don – W4DF

    • Hey Don, We can work something out. The cost of one from ebay and est. shipping to you is fine.  After some more testing I’m going to recommend you buy or build a High Pass filter somewhere above the UHF TV band (900 – 1000MHZ would be a good spot since your rtlsdr will work great on its own there). TV signals have been swamping me here in the middle of the L-Band. Puts the IF down in the 480-860MHz TV band. Depending on how high you are looking to receive you may want to do some additional mixing before or after the downconverter to bring the IF down some more (easy enough). Some of the deep space stuff is around 6-8GHz. Otherwise it should do the job, assuming you have a big ugly dish to help on the antenna side of things for deep space (9-10ft dish – old C-band sat TV style).

  2. 3 questions;

    1.What is the frequency offset/shift I need to use in software like sdr sharp to display the correct frequency?
    2.What will I be able to get using this without the mod?
    3. Can this be used for transmitting?

    • @JC 

      1. If working with frequencies above 2400MHz, enter 2,400,000,000. Frequencies below that you’ll need to just do the math in your head and remember that tuning is in reverse. Tune down to go up, and up to tune down. Upside-Down mixing below 2400MHz.

      2. Unmodified the Sup-2400 upconverts 250-750 MHz to 1650-2150 MHz. Not very useful for our general purposes unmodified. 

      3. Likely. A mixer is a mixer after all. BUT it may need further modification. (Something I’ll look at later if there is enough interest). Also filtering is something to be considered both internally and after the unit. You’d need to add amplification after the mixer stage and I would begin testing at less than -20-30dB or lower input power just to be safe.You may hit a few brick walls along the way.  I’ve not tried it yet and I would want to comb through the circuit pretty well and clean up any loose ends. Your external RF connections would be reversed. I have enough of them here I may try it later this week and make another post.

  3. Where do wires go for the external power?

    • @W4RD

      Normally you use a Bias-Tee (aka power injector) to power it. But you could add other external power by soldering connections to the LM7805 power regulator. I feed mine with a 13.8v (fed from a bench power supply) homemade bias tee.

      7805 pinout: From left to right Pin 1 is input (7-13.8 is enough to drive it. 9v battery would work for a time) Pin 2 (center pin is ground) and Pin 3 is output to the circuit, leave it alone.

  4. @kd0cq

    Thanks, I’ve received mine from the USA the other day, it did take about 4 weeks to come. I’m going to play around with it in the weekend. I’ve got some kanthal wire, which I used for chipping ps3 years back, that should be ok instead of magnet wire shouldn’t it?

    • @W4RD

      That should be fine, as long as its resistance isn’t too high. One thing to consider is keeping it from grounding out against the case etc if it doesn’t have any type of insulation.

  5. I actually found some bias-T’s at a thrift shop for 50 cents. The kind made by direct tv and say something about dc bias and 2150mhz on them. I hooked up a power supply and clamped the ground to the case and shoved the positive end’s wire in the appropriate antenna connector hole. At first I thought the 2150mhz upper rating might be a problem, but then remembered that the up/down converter outputs at a lower frequency. I think the major difference is I have it hooked up backwards compared to it’s intended use with these devices as it was meant to split powered satellite coax off of UHF TV, now it’s splitting the power off from the rtl-sdr and only to the converter. (note i haven’t actually done the mod yet to know how well this works or not)

  6. Dr op KD0CQ,

    I’m very intetested in this mod.So in this downconverter. Is there still one you can send me?

    73 de DE8MSH

  7. I am building a prototype for a project and think I need a more sensitive HackRF One that is Rx *only* from 4GHz -5GHz. I tried using the HackRF One for sensitive measurements around the 5GHz band and was unable to discern any measurable signal with/without the EMI kit and conducted the same tests with another HackRF One user and we arrived at same conclusion. The Rx sensitivity rolls off around 3GHz. I tried a low noise amplifier in attempt make any signal stand out to no avail.

    A HackRF user recommended a downconverter. That is what I am looking for at the moment.

    Do you have any suggestions or advice?


  8. Would you happen to know if there is a PCB & hardware difference between the Rev2 and Rev3 SUP-2400? As far as I can tell from looking online it seems to be a different color of plastic, but I can’t seem to really get a solid answer.

    73 – KC2OYX

  9. Hi,

    Is there a reason why it’s recommended to use Magnet Wire do to the patch ? Less loss in magnet wire ?

    Thanks for the tutorial, really cool stuff!


    • I reckon you could use what ever is available, but you need to remember you’re soldering it to very tiny points on the board, so smaller the better.. I’ve got magnet wire on hand so I just went with it.

  10. very cool. any chance you can provide before and after schematics?

  11. I want to be able to view the 2.4ghz waterfall of wifi, Bluetooth, rc radio tx, etc. with my rtl stick.
    I’m somewhat confident that I can do the soldering and de-soldering but can you explain more on the “bias tee” part? I’m just now learning about them.
    And how would everything connect together? (antenna>downconverter>rtl stick>USB port?)
    Do you have any pre-made ones for sale?

  12. Thank you Chris for the fascinating work. Is there a specific LNA & Bias Tee that is compatible with the 100khz-1.7Ghz SDR that you are using ? Thank you. ?

  13. Hey! Thanks for the great mod-guide! It still seems a little sketchy to me in regard to the power-feed to the sup-2400 unit? Is +5 VDC really enough to properly drive it? I’m considering using it together with my Airspy, as it already has a built in bias-t option available…

    • The system runs on 5VDC via the LM7805 voltage regulator. I don’t think the voltage from your Airspy will give it enough to run properly through the regulator. However, if you take the regulator out of the picture then yes, you should be able to run it just fine. There are a limited amount of active devices with the regulator out of the way so the current draw may be sufficient.

      I’ve got an Airspy mini. If I get time this weekend I’ll bypass the regulator and see how well it works.Since I got my HackRF I haven’t paid much attention to the sup2400, but the Airspy+downconverter should be an order of magnitude better on the RX side of things than the 8 bit HackRF or RTLSDR.

      Too many projects and not enough time.

  14. Hi: Thanks for the mod, ordered a unit, looking forward to sniffing 2.4g on my SDR!

    Do you have the before/after schematics? I like to attempt to understand what I’m doing . . . Thanks, John KD9BSD

  15. I’m hoping maybe you could help me out if one doesn’t want to use a bias tee can you maybe show what inductor to remove and the best place to tap the plus hot wire. I would greatly appreciate it.

  16. Hi,

    I received your mod from your shop (thx for making this available!).

    But when I want to check on 2.4Ghz (for wifi or bluetooth), I don’t see any changes.
    I’m simply using a 820T2 rtl-sdr with your device, and sdrsharp. Of course I shifted frequency setting. Antenna is omnidirectional 9db from a hamradio shop.

    Do I need to add hardware in the setup to make it work (filter ??), please?
    If so, do you have some part number for reference?
    As I see in videos you’re able to sense this band, I would love to do the same.

    Thx for your help 🙂

  17. Excellent job! I don’t understand where to connect power supply. 🙁 Could you advice me, please? Thank you!

  18. Has anyone tried changing the 9.375mhz LO crystal to a slightly lower value so as to lower the 2400mhz LO frequency to make the downconverter better suited for use as a simple wi-fi spectrum analyser when coupled with SDR. As it stands the 2400mhz oscilator makes it tricky for frequencies around 2400 ie 2385-2415mhz. In theory an 8.912mhz xtal should give a LO frequency of 2281.4.

  19. im not good at all with micro soldering like this ,
    is it possible just to canibalize the crystal along with few other parts and
    piece them together for a better circuit instead of this

  20. don bentley | May 26, 2018 at 6:53 pm | Reply

    im not good at all with micro soldering like this ,
    is it possible just to canibalize the crystal along with few other parts and
    piece them together for a better circuit instead of this

    • It’s possible but why would you do that when DirecTV’s done 95% of the work for you. By the time that you desolder all the chips and resistors that matter it’s going to be more work and a lot of these are actually needed.

  21. So I was just getting ready to do the tricky solder from the RF input to the capacitor in the far top left corner and I realized that 1: that whole section you are soldering to to the left of the capacitor is grounded to the case so you can connect that wire anywhere on the case or rail ( and thus making it a lot easier) and electrically should be identical and 2: that seems to me that that would be creating a short between the inner coax and the outer coax ground. Am I soldering to the wrong spot or is it indeed fine to have that shorted?

  22. Hurrah! Finally I got a website from where I can in fact gett valuable facts regarding my study and knowledge.

  23. Wonderful website. Plenty of useful information here.
    I am sending it to several buddies ans also sharing in delicious.
    And of course, thanks to your sweat!

  24. Great hack! Is it possible to simplify, or improve, if i ONLY need to receive Bluetooth? Thx!

  25. These modified available for 2.2 – 2.4 . Gotta to have some to monitor the Chinese lunar lander/rover ….help

  26. Pranay Jadhav | March 28, 2019 at 12:30 am | Reply

    Can we apply same mod to zinwell SUP 2400?

  27. For those of you who like to perform gambling and if you are usually looking for partners in gambling activities,
    Mabosbet is usually the right choice. Mabosbetransfer You can contact the customer care and make dealings with us.
    Mabosbet livechat is available 24 hours nonstop and is ready to serve you and help you online with gambling.

    Mabosbet. com as a new responsible gambling agent, we all always provide an option link to mabosbet to ensure members feel
    comfortable. You no longer need to have trouble obtaining
    an alternate Jababbet link with regard to access, it is previously available for you.

    We all also always give concern to the safety of our members, very strict protecting all the privacy regarding members
    of Jababbet.

    Trustworthy Mabosbet From 2010

    Along with good praise, the support from the Headquarters is no
    doubt. Friendly, quick response, under 3 minutes.

    Mabosbet is highly appreciated by gambling bettors coming from Indonesia
    because whatever triumph you get will be recognized by mabosvip.
    We constantly want to provide the great for members with
    optimum service. The site mabosmail. com is additionally very straightforward to access, when you only need internet access and alternate links mabosvip,
    no need to use proxies, newsletters, or troublesome applications.

    That will is why many folks join mabosbola and
    create deposits, then, win the particular match. The best and quality alternative mabosbola alternate site.

    Come join mabosbet. com the trusted on the internet gambling agent in Philippines.
    Contact livechat mabosbet today in the lower proper corner to
    get a user ID. Welcome in order to the club.

    MABOSBET will be a Trusted Online Betting Site that has been established for more as compared
    to 9 years with the greatest quantity of online wagering players.
    This gambling internet site also provides the
    most complete online gambling game with the most popular wagering providers in Indonesia.
    On the internet Gambling Games that may be played at MABOSBET are Sportsbook
    Soccer Wagering, Live Casino, Online Poker Cards Gambling, Online Slot Gambling and Online Togel.
    Mabosbet itself has provided a number of excellent facilities
    for online gambling players in Indonesia which range from 24-hour Live Chat Help, Bonuses with the easiest conditions, additional wins regarding True Gambling Players.

    This particular MABOSBET Gambling Site furthermore proves to get very trusted,
    while this Gambling Site can also pay regarding any winning player
    with no deductions. So you may play gambling comfortably in addition to safely without fear of paying.

    In addition to a definite win at MABOSBET, you will also offer
    additional bonuses to provide a different experience enjoying online gambling.

    Online Soccer Wagering has become a really popular gambling online game in Indonesia where every online game
    has a market regarding betting. MABOSBET has become an official partner of SBOBET Indonesia, where more compared to
    a decade has provided sports gambling games for gambling players in Indonesia.
    This specific SBOBET Soccer Gambling Marketplace allows a reasonable where participants will actually be
    given a live market from the established match directly.
    So you will certainly be very lucky in order to play
    SBOBET in this MABOSBET.

    Online slot gambling will be currently popular in Dalam negri, where online slots are extremely successful with huge
    jackpots and freespins that are simple to win. Because associated with that this MABOSBET 1st provided Online Slot
    Video games from 2012 for betting players in Indonesia. Exactly where Jackpot is provided even more than USD $
    1, 000, 000 for slot machine players who register in MABOSBET.
    The Slot Online game machine at MABOSBET does not just use
    your Stability, the Slot Game has been made with the FREESPIN Bonus that comes away more often, so you is
    going to be Fortunately.

  28. Mabosway stand-in sites and mobile sports login contacts – There are lots of
    online gambling agent sites scattered upon the internet.

    Each of these sites has offers and features provided, including the types of gambling games available.
    Many online gambling sites only offer 1 to 3 types of games and certainly
    have excellent games they offer. is an online gambling agent site that offers not without help 1 or 3 types of gambling games but 7 engaging types
    of gambling games that you can play. This proves that Mabosway
    is the most unchangeable betting site that offers not forlorn online soccer gambling, but
    Casino, Poker, Toto 4D, Bola Tangkas, Fish Hunter and online cockfighting gambling.
    This site is known as Mabosway Indonesia for members who arrive from Indonesia.

    Various types of online gambling games are adequately supported by the maximum sustain from
    One of them is the Customer relief feature which
    is 24 hours standby to further growth and invalidation transactions for members.
    How to register is also easy to do, especially for beginner bettors
    who are starting to bet for the first time.

    How to Apply for Mabosway

    How to register mabosway is definitely simple for secret people
    who desire to start playing online gambling.

    You by yourself have to click the link NOW button upon the home page which will go directly to
    the registration form page. After successfully registering you will acquire
    a user ID as an identity in the game. After all is done, you are officially joined and become a member.

    After you officially become a advocate you are offered to pick the type of
    online gambling game that you can play. Here are 5
    types of favorite online gambling games that you can take
    action at

  29. The subject of gambling has indeed become one of the most hurting topics of conversation in Indonesia.
    Not unaided authenticated problems, in Indonesia
    gambling is underestimated from various aspects ranging from culture,
    religion, social, even people who do something gambling always have
    a negative connotation regardless of whether the person is flourishing or not
    in this industry.

    In contrast to developed countries that are more get into
    to the spread of the gambling industry. There, professional gambling
    players are considered celebrities, are renowned and are covered in television shows.
    Hailed and inspired to many who saw it, what a sight that is entirely lame in comparison.

    It is undeniable, considering viewed from an point toward
    dwindling of view, gambling games both offline and online have evolved into a event
    commotion that give support to many parties. Not abandoned the organizers but
    afterward those who work it and some of the parties on the order
    of it such as people who exploit in the field of information technology and executive who
    get the tax.

    Like any further business in the world, gambling comes once its
    own risks and rewards. No one can truly leave suddenly losses
    or continue to create profits in his business, there are always unavoidable
    losses and profits will continue to be pursued. What we
    can do for event is to locate the best strategy to minimize
    losses and accumulation profits at any time.

  30. Userbola is a trusted maxbet agent that has collaborated with official maxbet providers since 2014.
    All of us are tasked with serving betting players who wish to
    sign up for an established maxbet account in Indonesia.
    We here as a maxbet list site also have an official PAGCOR license to market online gambling games.

    In addition, Userbola as a maxbet agent always becomes positive
    input from betting members such as fast transaction services, safe payments and complete betting
    games. The data of members who have registered at a trusted maxbet agent userbola are
    also protected securely. The userbola team also always provides benefits to all betting members
    every week such as a rebate reward or cashback that you will not get
    on the official maxbet site. From the assessment in our betting members and official providers who may have made userbola the amount 1 trustworthy
    maxbet agent in Indonesia.

    How to Register a Maxbet Account
    Gambling online players who want to sign up for a maxbet account through the trusted maxbet
    list site userbola only need some important data like the full name in line
    with the bank account, account number, contact number that
    can be contacted, and email address. These data can be completed via the registration form on our website.

  31. customary and thank you for visiting online casino agents for
    Indonesia. Here we are here to meet the expense of admission for fans of sbobet casino who desire to join the
    international agent site Promosbobet.

    The products offered are unquestionably diverse and are
    categorically the best choice. Derived from providers that
    have credibility and have been proven to have the best
    predicate in serving their customers. Providers past Sbobet, Maxbet and
    many more.

    As the best online casino and soccer gambling site in Indonesia.
    We provide maximum serve in imitation of customer sustain that works online 24 full hours every day.
    so members can play a part whenever and wherever without fearing to
    approach the possibility of difficulties or confusion.

  32. Not many online gambling sites in Indonesia have endorsed event status and have licenses issued
    by relevant authorities. In addition, the level
    of consumer support for online gambling sites can yet be agreed low because of the 100 manageable
    online gambling sites, unaided just about 10-15 sites are
    nimble to come up with the money for professional sustain and meet standards.

    Therefore, you cannot arbitrarily choose an online gambling site to be a playing
    partner. There are many criteria and factors
    that must be considered to make an online gambling site a area to shelter and keep game deposits.
    However, it will agree to become old and effort to find
    a trusted site taking into consideration this.

    Hence, in this article we would like to have enough money important recommendations more or less
    trusted and ascribed online gambling sites in Indonesia.
    By becoming a fanatic of this gambling site, it is clear that you will be forgive
    from doubt and one step closer to success. Online gambling is no longer just
    a game but a thing that can consent you to a brighter future.

    Like any extra matter in the world, all step you recognize will
    have alternative risks and benefits. No human swine can always make a gain in all
    business, and no one can always avoid losing.
    every that can be ended is to minimize losses and addition profits until finally
    the profits make losses not felt.

  33. good enough and thank you for visiting online casino agents for Indonesia.
    Here we are here to manage to pay for permission for fans of sbobet casino who want to associate
    the international agent site Promosbobet.

    The products offered are categorically diverse and are unconditionally the best choice.
    Derived from providers that have credibility
    and have been proven to have the best predicate in serving their customers.
    Providers similar to Sbobet, Maxbet and many more.

    As the best online casino and soccer gambling site in Indonesia.
    We present maximum utility as soon as customer retain that works online 24 full hours all day.
    suitably members can play in whenever and wherever without fearing to twist the possibility of difficulties or confusion.

  34. Sbobet is a trusted gambling site that operates to assist every fans of online gambling in the
    world. Founded in 2010, it didn’t take long for Sbobet to become the
    biggest online site in Asia and as soon as it comes to the amount of betting keep that rotates
    all week, Sbobet is as well as one of the biggest
    sites in the world.

    Sbobet is certainly popular, especially in the middle
    of Asian bettors, the excuse is that the site has been awarded as the best gambling operator for two
    years in a row. It offers a variant of football betting in the
    manner of unconditionally low margins as soon as compared to extra sites in its class.

  35. Mabosbet has been present in the best soccer gambling site industry for
    a long time, presenting various kinds of soccer games for fans in Indonesia from various walks of life.
    Games easy to get to at Mabosbet total the most well-liked games such as guessing scores to venturesome exotic
    gambling games such as Asian Handicap and amalgamation Parlay.

    Customer facilitate is swift 24 hours a day and can be contacted easily through various
    methods including stimulate talk directly from the official website, proving
    that we are the best online gambling agent site later than the
    most professional service. Register yourself now and enjoy the gambling game following millions of members from every exceeding the world.

Leave a Reply to JC Cancel reply

Your email address will not be published.


This site uses Akismet to reduce spam. Learn how your comment data is processed.